A converter in Brazil placed a 15 ton order of 8011 O temper aluminum strip in 0.089mm thickness and 60mm width, slit for cigarette tube wrapping. The material is used on high speed tube forming lines, where a gauge variation of a few microns or a burr on the slit edge is enough to stop the line and create waste. The order was produced, inspected and shipped as a single lot so that every coil on the line behaves the same way.
- Alloy and Temper: 8011 in O temper, soft and fully annealed for forming without cracking.
- Gauge: 0.089mm, held within a narrow band across the full coil length.
- Width: 60mm slit strip with a clean, burr free edge for the tube forming and gluing process.
- Quantity: 15 tons, delivered as one production lot to keep properties consistent.
- Destination: Brazil, by sea freight with export packing for a long ocean voyage.
8011 is an aluminium iron silicon alloy that combines good formability with a fine, uniform grain after full annealing. In O temper the strip stays soft enough to fold and glue at high speed without spring back or edge cracking, while the alloy still gives enough strength to keep the tube wall rigid after forming. Compared with a pure 1000 series strip, 8011 holds a more stable surface after annealing, which matters when the foil is printed or lacquered before tube forming.
![]()
- Rolling to Gauge: The strip is rolled on a cold rolling line with online thickness measurement, then finish rolled to 0.089mm and checked coil by coil against the agreed gauge band.
- Annealing: Full anneal in O temper to reach the required elongation and a soft, formable structure, with the mechanical properties confirmed on samples from the head and tail of each coil.
- Slitting to 60mm: Slitting is done with correctly set circular knives and a controlled overlap, then the edge is inspected for burr, waviness and width deviation.
- Surface Control: The strip is checked for pinholes, scratches, oil marks and roll marks, because surface defects show up clearly on the finished tube.
- Winding Tension: Coils are wound at a controlled tension and even traverse, so the strip unwinds smoothly on the customer line without telescoping or edge damage.
- Inspection Before Packing: Each lot is checked for gauge, width, mechanical properties and surface, and the inspection record is issued with the shipping documents.
- Coil Packing: Coils are wrapped with protective paper and plastic film, suspended on a sturdy pallet or packed in wooden cases so the edges are not crushed in handling.
- Moisture Protection: Desiccant is added inside the packing, since thin annealed strip can stain if condensation forms during a long sea voyage.
- Loading: Coils are loaded eye to wall and braced inside the container to prevent movement and edge damage.
- Documents: Commercial invoice, packing list, bill of lading, certificate of origin and mill test certificate were issued for Brazil customs clearance.
The 15 ton lot was produced and shipped on schedule, with gauge and width results recorded coil by coil and the shipment released only after the final inspection. Because the whole order came from one production lot, the customer can run the same forming parameters from the first coil to the last, which keeps line speed stable and reduces waste at start up. The same specification is now kept on file for repeat orders, so a reorder can be confirmed against the existing drawing without a new trial run.
- For thin slit strip below 0.1mm, gauge consistency matters more than the nominal thickness on the certificate.
- Edge quality on slit strip is a process parameter, not a cosmetic point, so burr and width deviation must be inspected, not assumed.
- One lot production removes batch to batch variation, which is what high speed tube forming lines need most.
- Packing and moisture control decide whether the material arrives as it left the plant on long ocean routes.
If you are sourcing 8011 O aluminum strip in thin gauge and narrow width for cigarette tube wrapping, cable shielding or other precision conversion, send us your alloy, temper, thickness, width and quantity. We will confirm feasibility, packing and lead time, and provide a sample for a trial run before the bulk order.


